All Posts by Eric Blumer

Safely Removing A Fiberglass Shower From Your Home

How To Remove Fiberglass Shower

Remodeling your bathroom can be a scary undertaking, especially if you've never done anything like it before.  I want to show you that with the proper technique, there isn't anything to be scared of.  You must be careful and diligent while working, and be sure to watch your surroundings as well.  I will start by saying that if you're removing a shower (similar to the one in the video), turning off the water is a good idea.  Accidents do happen, and an open water line can discharge about 15 gallons of water a minute.  We are starting with a fully functioning shower and going step by step from there.

Step 1.

Removing the faucet is the first thing we will have to do.  If you are planning on re-using your faucet, it's important to be careful with it.  With most faucets there is a trim mounted over a set screw.  The faucet in the video has a friction ring that snaps over the handle to hide the set screw.  Many faucets use a small allen screw to hold the trim on.  Once the outer trim is removed, removing the set screw is easily done with a philips screw driver.  Usually a philips screw driver is also used for the trim plate screws as well.  The shower head should unscrew from the wall by turning it counterclockwise.  Once all the trim pieces are removed you are ready to go to the next step.

Step 2.

We still have to remove the base trim from the walls adjacent to the shower.  The base trim we are removing is painted, and therefore caulked to the wall.  We use a utility knife with a sharp blade to carefully cut the caulking at the wall.  If you intend on re-using the base trim it's again important that you take your time here.  We have really good luck moving slowly and methodically  with our pry bar during demolition so that we don't create more work for ourselves in later steps.  To remove the nails in the base trim it's always best to pull them through from the back.  Pulling the nails through the back prevents the face of the trim from being damaged.   We use linemans pliers to pull the nails through.

Legacy Bath And Tile Logo

Step 3.

Draw reference lines.  This may seam unnecessary, but if it's your first time pulling out a fiberglass shower it will help.  The shower will have a flange that ranges from 1"-1.25" wide from the edge of the wall.  Draw your line at least 1.25" away from the edge of the shower to reveal the flange completely.  If you don't remove the flange, it will leave a bow in your drywall making the tile not sit flat.  This will give an unsightly appearance when the job is completed.

removing screws that hold fiberglass shower in place

Get Your Free Bathroom Remodeling eBook

  • 1
    Design ideas for your space
  • 2
    Details every bathroom should have
  • 3
    Add value to your home

Step 4.

Cutting out the drywall.  I start by cutting the drywall out of the way first.  This will reveal the flange so that you can remove any screws or nails that may be present.  I am always surprised to see how many showers are held in place with only two nails.  Two nails isn't nearly enough for proper installation, but that's a different issue.  Once the flange is revealed and the fasteners are removed it's time to move to step 5.  

Step 5.

Time to cut out the shower walls.  Again, I would draw reference lines in the shower itself for you to cut along.  The lines will help guide you, but it's not a big deal if you don't stay on them exactly.  I recommend cutting the walls at the corners (two cuts) and then along the bottom of the shower (one cut).  The wall cuts and floor cuts should intersect making the shower come out in four pieces.  I find it best to cut one wall first, then the floor cut past the first wall cut.  I remove each piece of the shower as it's cut apart to help prevent binding and stuff falling on me.  Removing the pan is the next step.  For this step you want to keep the saw as shallow as possible.  There is plumbing behind the shower and possible electric as well, don't cut too deep so that you minimize the chance of cutting pipes or wires.

using a sawzall to remove a fiberglass shower in columbia mo

Step 6.

Now that the walls are out it's time to cut out the pan.  I use a multi-tool saw to cut around the shower drain, but a sawzall works as well.  You don't want to pull the pan up before the drain pipe is cut out as you risk damaging the connecting plumbing.  It might be a good idea at this point to let you know that mouse homes are very common here too.  I don't usually find live mice, but it's common to see where they have dragged insulation into the shower pan cavity at some point.  Rest assured that your tile shower will have no such place for them to call home.  Oh, back to the shower pan removal.  Sometimes it's necessary to cut the pan in two pieces as the walls can be too tight to allow you to just tip it out of the way.

Step 7.

Clean up the space where the shower used to be.  Make sure that any mortar that supported the shower (yeah, right) is also removed.  I say "Yeah, right" about mortar because even though the shower is supposed to be set in mortar it never is.  It's just another thing that prior trades messed up that you won't have to worry about any more.  New home construction budgets are apparently so tight that $8 worth of mortar is too expensive.  I think by now your shower is out of your way, you can start planning your new installation from here.

mouse nest under shower pan
Multi-function shower, horizontal niche, Columbia Missouri, certified tile installer

Tile And Grout Maintenance – Keeping Your Tile Looking New

Germs, disease and bacteria is everywhere.  How can you protect yourself and family from the dangers that you can’t see?  Did you know that tile is a natural repellant to the problems listed above?  Using tile in your home is a low maintenance solution that looks wonderful.  Let me show you why tile should be your finish material of choice.

Naturally Resistant To Microbial Growth

Man-made tile (such as porcelain, ceramic and glass) are made of inert materials and are resistant to bacterial growth.  Actually, the entire assembly for tile installations are very resistant to bacteria growth.  Bacteria needs a very acidic environment to grow and tile installations are very alkaline.  Properly installed tile will naturally have a strong resistance to mold and mildew growth.

What do I mean by tile assembly?

Moldy green drywall, tile shower failure, Columbia Missouri, improperly installedThe tile assembly includes concrete board, thin set mortar and cementious grout.  Cement naturally falls on the high end of the PH scale (alkaline).  Mold, mildew and bacteria need a low PH to survive (acidic).  How does a tile assembly, then grow mold you might ask?  The short answer is improperly installed tile.  When water containing skin cells is trapped in the substrate, the PH can change from high to low.  This is the perfect environment for mold to grow (humidity, food source and temperature).  This is why it’s important to hire only qualified installers to build shower assemblies.  Our bathroom remodeling procedure.

Caring For Your Tile

Proper tile maintenance is very easy.  My typical recommendation is warm water, a nylon bristle brush and elbow grease.  Because tile is so resistant to bacteria, I don’t recommend any harsh chemicals.  If you want to use a chemical, be sure it’s PH neutral.  A cleaner on one extreme or the other on the PH scale will deteriorate your grout and open poors.  That will make it easier for future stains to penetrate and the cycle will continue.

Wrapping Up

What do you think of tile?  Is it something you currently have in your home?  If you have a question regarding tile installation post it in the comments below, we’d love to hear from you.  For great tile selection in Columbia Missouri, check out Legacy Bath & Tile.

Custom shower installer, Mid-Missouri

Failed Tile Showers Are Expensive To Replace

We have the opportunity to work for a historic hotel in Boonville, Missouri.  In 2008 or so the hotel had custom showers installed in their building.  The custom shower installer they used, unfortunately was not aware of proper waterproofing techniques.  Today, the showers are starting to fail and cause liability concerns to the owners.  I’m writing this post to help you avoid making the same mistake.  There are many failed tile showers in the area, I don’t want to see your home added to that list

Overview of the Bathroom Construction

Before we get into what went wrong, let’s look at what went right.  The entire bathroom floor of this room is treated as a wet area.  There is no evidence of water leaving the bathroom and leaking onto the ceiling below.  Under this room is the dining room of the hotel, I’m sure we would know if the floor was leaking.  I’m still not sure how the floor isn’t leaking and the walls are falling apart.  I haven’t seen that before.

What Method Was Used?

Custom shower installer, Columbia MissouriThe custom tile shower installer of this bathroom used green drywall as a substrate.  He tiled directly over that with no further waterproofing.  Given the small tiles used, water was easily able to penetrate into the drywall.  Once the drywall was wet, it wasn’t able to dry out again.  You can see the mold on the green drywall.  Obviously, green drywall can mold (so can any other drywall, no matter the color).

Finding A Good Custom Shower Installer

If you’re looking for a good custom shower installer, start by looking at trade organizations.  The N.T.C.A. and C.T.E.F. Websites are good starting points.  I would also recommend asking the potential custom shower installer what method they use to build showers.  At this point you should also ask about their warranty.  Again, the shower we are working on here is about 10 years old.  I would stay away from any contractor that only offers a 1 year warranty.  For more information, read my article on properly installing tile assemblies.

Properly Installing Tile Assemblies – What You Need To Know

You know, nothing beats tile when it comes to beauty and durablility.  That’s why you want tile in your home.  You are doing your due diligence and getting multiple bids for your project.  How do you decide which contractor to hire from here?  One thing you’re certain to find is that the costs are all over the place.  It’s not uncommon for some estimates to be different by 40-50%.  In some instances that’s thousands of dollars different.  Let me encourage you to read this article completely.  It will help you  determine who is qualified to do your project, and who isn’t.

American National Standards Institute (ANSI)

ANSI A108, ANSI A118, ANSI A136 handbookTo ensure that tile assemblies last a long time, and that they are predictable, ANSI testing is done.  ANSI tests everything and labels the approved method accordingly.  Tile methods are contained in ANSI A108, ANSI A118, and ANSI A136.  I will be making references to those standards throughout this article.  Don’t hesitate to ask any questions you may have at the bottom of this article.

Workmanship standards (ANSI A108.02)

There are standards for acceptable workmanship.  No job is going to be perfect, but they shouldn’t be sloppy either.  For the most part people can determine for themselves what’s appropriate and what isn’t.  In the unlikely case of litigation, these are the standards that would apply.  This standard covers allowable lippage, grout spacing, grout sizing and other visual aesthetics.

Grout spacing

Many homeowners want the grout lines as tight as possible.  I use the smallest joint I can given the tile I have to work with.  Most porcelain tile can accommodate a 3/16” grout joint.  To get a smaller joint, you will need a rectified porcelain tile.  There are size differences between each tile.  The grout joint is determined by finding what that difference is (usually 1/16”) and multiplying it by 3.  That’s why a 3/16” joint is typically the smallest we can do.  No grout joint for porcelain tile should be smaller than 1/16”.

Substrate Preparation (ANSI A108.01)

Before we begin to think about setting any tile, we need to know if the substrate is ready.  We need to know if the substrate is strong enough to support the tile we want to use.  It’s also necessary to know if the substrate is flat enough for the tile we want to use.  The type of tile will have an effect on both questions.  A natural stone installation, for instance, requires a wood subfloor to be twice as rigid than a porcelain tile requires.

The substrate must be flat

How flat it has to be is determined by the tile itself.  Standard tile, with no edge 15” or longer, requires a deviation of no more than 1/4” in ten feet.  Tile with an edge 15” or longer requires no more than 1/8” in ten feet.  The larger the tile, the flatter the substrate must be.  This is true for both walls and floors.  Most concrete surfaces do not meet either requirement, making the use of self leveling cements more likely.

A wood subfloor must be rigid

For standard tile installations, the subfloor must meet L/360 deflection requirements.  L/360 is a load calculation based on the span of the floor joists and the floor joist material.  Floor joist span isn’t based on the size of the room, but the distance between the supports of the joists themselves.  Natural stone tile requires a load of L/720 and double layer plywood before tile installation can begin.   The installation of a second layer of plywood must conform to APA (American Plywood Association) standards.

Tile Underlayment Considerations

There are many things that should be considered when choosing a tile underlayment.  Let’s look at what it takes to properly install tile underlayments here.

Concrete board installation

Concrete board can only be installed over wood substrates, it shouldn’t be used over concrete slabs.  All concrete boards require thinset mortar under them for support.  The thinset is not to bond the concrete board to the plywood.  Concrete boards need to be spaced 1/8” apart from each other and the sheets must be staggered.  Alkali resistant tape must be used on the seams of concrete board as well.  The alkali tape makes the concrete boards behave as one, expanding and contracting.  Skipping the alkali tape increases the chances of reflective cracking appearing around the sheets.

Uncoupling membranes

DItra XL in BathroomWe prefer to use uncoupling membranes as much as possible.  The only time we cannot use an uncoupling mat is if the tile is less than 2” on each side.  This is due to point loading concerns.  Schluter Ditra is our mat of choice.  Ditra allows the substrate and tile to expand and contract separately from one another.  This means that reflective cracking is not a concern for me with Ditra.  Schluter Ditra can be used over concrete or plywood substrates.

Other uncoupling mat benefits

Ditra is waterproof.  Many times when a basement is to be tiled moisture migration is an issue.  The end result of moisture migration is typically efflorescence.  Efflorescence is salt deposits left behind, usually in grout joints.  Ditra practically eliminates efflorescence because of the air cavities integrated into the system.  The concrete subfloor is still able to breathe, the moisture is just re-directed to the perimeter of the room.

Waterproofing Considerations

There are two ways to correctly waterproof a shower.  Both systems are independent of each other, and should not be mixed together.  In other words, use all of one or the other, not parts of both.  The first method we will look at is called water in, water out.  This method consists of cleavage membranes and pan liners, water is managed through primary and secondary drains.  The next method is called sealed systems.  In a sealed shower the waterproofing material is located immediately behind the tile layer.  This allows the shower to dry faster and there is only one drain.

Water in, water out

This is an old method of building showers, and one that works well if executed properly.  This method takes the most skill and has  the most steps involved, making a failure more likely.  Looking at the picture, you can see several of the steps involved.  There is a three piece clamping drain that has its base located at the base of the shower receptor.  This is the secondary drain.  Water will migrate through the mud bed layer into this secondary drain, so protecting the weep holes is very important.  It’s also important that the fastener schedule be followed as well.  No penetrations through the curb (inside or top) and no fasteners located below 3” above finished height of the curb either.  This is where most of these showers fail, is not following the fastener schedule.

Sealed showers

Schulter systems waterproofingAs I mentioned earlier, the waterproofing is located immediately behind the tile.  In other words, the tile is bonded directly to the waterproofing material.  This means that the water won’t travel through a mud bed to a secondary drain.  A bonding flange drain is what makes this system possible.  The waterproofing material should be installed at least as high as the shower head all the way to the drain.  Every square inch of the shower must be waterproofed, not just the seams and corners.


Flood testing

Every tiled shower must be able to pass a flood test.  Both water in, water out systems and sealed showers require flood testing.  A flood test means that once the waterproofing is installed, the shower pan is filled with water for 24 hours.  We are looking for any shower pan leaks.  Many water in, water out systems will pass this test as it’s done before the wall board goes up.  I am a proponent of testing the shower pan when the installer is ready to set tile, not before.   Even a finished tile shower should still pass a flood test.  Simply remove the drain cover and fill the pan with water.  If your shower has a three piece drain, make sure the plug is located at the base of the drain.  Water can go around the upper section of the drain and give you a false sense of failure.

Vapor drive

Vapor drive is when one surface is wet, and immediately behind it is dry.  We know that moisture will migrate from the wet side to the dry side.  That is vapor drive.  As buildings become tighter and tighter, I recommend not using water in water out showers.  They don’t manage the moisture in the system as well as the sealed shower does.  The vapor drive of the water in water out system is more likely to get trapped in stud cavities and cause mold growth.  If you know your home is pretty air tight, use only a sealed shower system.

Approved substrates for walls

Concrete board and other similar boards should only be used for shower construction.  Do not use Sheetrock, no matter what color the paper is.  There is not a single Sheetrock manufacturer that will have instructions for installing their product in a shower.  Concrete board is not waterproof.  Install  6 mil plastic behind the concrete board or surface applied on top.  Always use plastic or a surface applied membrane, never both.  Using both plastic and a membrane can trap moisture in a moisture sandwich.  A moisture sandwich is typically a breeding ground for mold growth.

Drywall is ok for dry areas only

If you’re tiling a backsplash or accent wall that is not in a wet location, drywall is fine.  Drywall is a good substrate for bonding tile, as all types of mortar stick well to it.  If you are going to tile over drywall, don’t use joint compound.  Drywall mud and tape are bond breakers for tile.  If you use joint compound be sure to paint over it prior to setting your tile.

Mortar Types – What You Need To Know

There are primarily 4 different types of dry set mortar (thinset) as well as organic adhesives (mastic).  Knowing when and where to use these mortars will have a drastic impact on the performance of your project.  Each type of mortar and mastic is identified by it’s ANSI rating (A118.1, A118.4, A118.11, A118.15 and TYPE I, or TYPE II for mastic).  I will give a brief description of each below.


Both mastic types can be used almost interchangeably, TYPE 1 mastic has a higher shear strength requirement.  Mastic has mold inhibitors as part of its mix.  Mastic can only be used on walls of a shower or tub surround, never the floor.

Non-modified thinset mortar (A118.1)

Schluter set mortar, Columbia MO, certified tile installerNon-modified thinset mortar can be used to install concrete backer board. This mortar can also be used directly over concrete or drywall as well when installing ceramic tile.  It is typically not recommended for use to install porcelain tile.  However, when A118.1 mortar is used over an impervious material (such as Ditra or Kerdi) the installation of porcelain tiles is fine.

Modified dry-set mortar (A118.4)

Mortar meeting A118.4 requirements can be used over nearly any substrate except plywood.  The modifiers in A118.4 mortar make it stick better to both the substrate and the tile.

EGP Mortar (A118.11)

Exterior Glue Plywood mortar is used for bonding tile directly to plywood substrates.  This mortar is also required for bonding uncoupling mats to EGP as well.  Never bond tile directly to the subfloor.  If you are using EGP as a plywood underlayment, it must be a double layer installation.

Improved modified dry-set mortar (A118.15)

Many improved mortars are also fast set mortars.  Mortars that fall under this category have more modifiers built in and are far stickier than the ones listed above.  As you can imagine, the further down this list you go (with the exception of mastics) the more expensive the mortars get.  Mastics are always more expensive than mortar (including the 118.15 mortar).

Other Mortar Considerations

All mortars are available in both white and gray, typically.  Many manufactuers also offer the mortars in thixotropic options as well.  Thixotropic mortar (formerly called medium bed mortar) will hold its shape until moved.  Ketchup, is thixotropic.

Not leveling agents

Thinset mortars are not designed to correct substrate flatness, no matter what type of mortar it is.  If the substrate needs correcting a proper material should be used (self leveling cement over concrete, for example).  Mortars are designed for the installation of tile only.  It is recommended to stick to manufacturer requirements always.  This brings me to my next point on proper mixing of mortars.

Always Follow Manufacturer Mixing Instructions

All cementious products have a high chemistry formula behind them.  It’s important to follow each manufactuer’s written instructions on how to properly use their products.  Every manufacturer will put the proper mixing instructions on each individual bag of material you use.  Mixing mortar is not a guessing game, nor is it appropriate to mix it to the consistency you prefer.  We use measuring buckets for water and dry material and a stop watch for mixing.  It is especially important that self levelers are mixed exactly as well.   THERE IS ABSOLUTELY NO WIGGLE ROOM ON SELF LEVELING CEMENTS.

Grout Types

As with all other products, there are good, better and best grouts as well.  Sanded and non-sanded grouts will be the introductory products (A118.6).  High performance cement grouts are A118.7 and epoxy/urethane grouts are A118.8.  With each class upgrade a more stain resistant grout is achieved.

Sanded/unsanded grout (A118.6)

Sanded grouts are used for joints 1/8” and larger while unsanded is used for joints 1/8” and smaller.  These grouts are more susceptible to pigment washout, so installer care is a must.  If this type of grout is to be used on your project, I highly recommend sealing it as well.  This grout class has the least resistance to staining.

High performance cement grout (A118.7)

Most grouts in this category can be used from 1/6”-1/2” using the same mix.  These grouts typically have reduced silica in them allowing them to be used in smaller joints.  The stain resistance properties of this grout is also much better than with A118.6 grouts, though these grouts can be sealed if desired as well.  Color consitancy of this grout class is also superior.  It’s much more difficult to wash out the pigment when grouting. This is the minimum grout I recommend for all our projects.

Epoxy and urethane grouts (A118.8)

Epoxy and urethane grouts will have the most resistance to staining and be the most color consistant.  Some epoxy grouts are actually labeled as stain proof in residential settings.  If you want a one time application and no further worries, epoxy grout is a great addition to any project.  There are also added effects that epoxy grouts can do as well.  Glow in the dark and glitter are just a couple of additive types you can use with epoxy.


I only recommend the use of color matched silicone with the grout of your choice.  Siliconized latex or acrylic caulks will shrink and crack in a short amount of time.  100% silicone is also the only type of sealant that should be used in wet locations as well.  All change of planes (floor/walls and wall corners) should have a sealant instead of hard grout.

Movement Joints (EJ 171)

Physics says that all objects change size with load, temperature and humidity.  Tile is no different.  Every job requires the use of movement joints.  We always leave the perimeter of the room open for movement (1/4” minimum).  Additional movement joints may be required in the floor itself as well.  No tile installation should be larger than 24’ in any direction without additional movement accommodations.  Rooms that have a lot of windows or tile located outside should have movement joints no more than 8’-12’ apart.  Tile will tent and fail without the proper use of movement joints.


This article is just the tip of the iceberg on the knowledge it takes to properly install a tile assembly.  The information listed here is definitely not complete, and should not be used as the only source of education.  My intent for writing this post is to illustrate that most installers have no idea what it takes to properly build an assembly.  If you are an installer and this information is new to you, let me encourage you to seek further education opportunities.  The NTCA and CTEF have training events all over the country encouraging installers to do better.  I have attended many of these educational seminars and plan to attend many more.


If you are a homeowner looking to hire a tile installer for your project, please ask them questions.  Your job should not be a training ground for an unqualified tile setter.  I am all for educating installers, and that typically comes from working for a qualified installer first.  Don’t assume that because they have been in business for “x” number of years without a failure (that they know about) means they know what they’re doing.  Unfortunately many installers never educate themselves more after they install their first tile.  Your shower will see more water per year than your roof ever will.  A small leak will cause thousands of dollars in damage to your home.  Please find out all you can about your potential contractor before the work begins.

Thank you very much for reading this article, I hope you found the information valuable.

Columbia Missouri tile shower installer, lifetime warranty

10 Questions To Ask Your Tile Shower Installer

Having a tile shower installed in your home can be the greatest decision Central Missouri tile shower installeryou make regarding maximizing it’s value.  The worst thing you can do is hire an unqualified tile shower installer to build your new shower for you.    I hate going into a clients home and seeing a shower less than two years old that has to be replaced.  My hope here is that I can help you qualify your installer before hiring them to do your project.  If you follow this guideline, your odds increase that your new tile shower will last a lifetime.  For a more in depth look, read this article on proper tile assemblies.

Tile Shower Installer Qualifications

  • What is their warranty?

    Most installers offer a one year warranty from the date of completion.  Since most of the failed showers we see are older than that (by a few months) I would ask for a longer warranty.  For example, we warranty our showers for life.  You get both our warranty and a lifetime manufacturer warranty as well.

  • What is their preferred waterproofing system?

    You are likely to find many different answers to this question.  What you are looking for is a complete system installation method.  A tile shower installer that says I use this membrane, and this paint on product is a red flag.  Using multiple manufacturers on a shower means you won’t have any kind of warranty from them.  Now you will rely solely on the knowledge of the installer only.  For example, our lifetime warranty is provided by Schluter Systems.  This post details our shower construction method.

  • Does the installer have any memberships or certifications Mid-Missouri tile shower installerfrom the tile industry?

    A good way to check for a tile shower installer’s qualifications is to look for certifications and memberships.  The N.T.C.A. (National Tile Contractors Association) as well as C.T.I (Certified Tile Installer) are good sources to look at.

  • Basic Contractor Qualifications

    These questions are just contracting 101 to me.  Hopefully the potential tile shower installer you are interviewing doesn’t tell you only what you want to hear.  I hope for everyone’s sake, they answer honestly.

  • Does the tile shower installer stay on your project until it’s finished?

    A lot of contractors start a job right away, then leave to start another job instead of finishing your job first.  I would ask the potential installer if they stay on your project until it’s completed or they will be leaving to start other jobs.  We only work one job at a time.  Sometimes this costs us other work, but I would rather have a happy customer instead of two dissatisfied customers.

  • What is their daily work schedule?

    It’s important that your tile shower installer keep a regular work schedule.  Not only will having a consistant start and stop time make their progress more predicable, it will also help you as well.  Typically, we start our day at 8:00 and work until 4:30

  • Are they licensed and insured?

    A good tile shower contractor will carry both general liability insurance and workman’s comp insurance.  Both types of insurance are there to protect them and you.  Be sure to ask for verification of their insurance prior to them beginning work.

  • What are their customer reviews or references like?

    A good contractor keeps records of happy clients.  Many homeowners today even post their review of the company online.  Be sure to look for reviews of their company before hiring them.  I would recommend using the reviews only as a measure of them personally and not how knowledgeable they are.  Many happy customers leave a review shortly after the work is completed and don’t update their dissatisfaction years later.

  • What are their jobsite safety protocals?

    Good contractors know that protecting their employees as well as their customers is very important.  I would ask them about grounded tools (especially wet saws or other equipment that’s around water).  Also find out how they clean up during and after the day is over.  Keeping a clean worksite is very important.  We use drop cloths, HEPA air scrubber and plastic sheeting hung from the ceiling.  We also provide house cleaning after the job is complete.

Other Considerations

  • What if you want something changed?Tile shower installer Columbia Missouri

    Let’s face it, sometimes a tile or other feature just sticks out and you don’t like it.  How does your potential tile shower installer handle such things?  For us, we don’t argue with you.  If you don’t like a tile, we will replace it with one you do.  We do work with you to locate fixtures and other finish items as well before we install them.  We do want the job to be right the first time, but at the end of the day we want you to be satisfied as well.

  • How does their billing work?

    It’s good to ask this question prior to the start of the job to help clear the air on expectations.  Some contractors want a check to hold your spot, while others want to be paid completely in advance.  We do collect a check the day we start for 50% of the job.  If your job takes longer than a week, 50% of the remaining balance is collected on Friday.  Our final payment is due at job completion.

I apreciate that you took the time to read through my suggestions.  Be sure to comment below and let me know what you think.  If you have a question you would like to see added, comment that below as well.  We are a tile shower installer servicing all of Mid-Missouri.  Good luck on your project, I hope it is a successful one.


Hexagon tile shower floor curbless shower

Barrier Free Showers Aren’t Just For The Elderly

Starting your day with a shower used to be your favorite part of the morning.  Just like your morning coffee, a shower is invigorating and gets the blood flowing.  Getting older has changed that, and now there’s a fear of not getting over the step into your shower.  Therefore, a zero entry shower is the answer you’re looking for.  If you aren’t ready to move into an assisted living facility, I want to help you.  Let me show you how easy it is to add a curbless shower into your home.  Continue reading to see some great benefits of adding a zero entry shower into your home.

A Curbless Shower Is Visually Appealing

You don’t have to be in need of an accessible shower to appreciate the look of a curbless shower.  Unlike many accessible features, a curbless shower blends in with the surrounding area easily.  It is also worth noting that a zero entry shower is much easier to keep clean as well.  Think about it, one of the hardest areas to clean is the wall to floor transition. If you use a zero entry shower you eliminate the floor to wall transition in that area.  Another way a curbless shower is visually appealing is in it’s simplicity.  Eliminating the curb makes your shower appear larger, and that is another great benefit.

Installation Considerations

Installing one of these showers takes quite a bit of skill to do correctly.  With a standard shower the curb will help contain water from the faucet.  The water management system for a curbless shower needs to be properly installed.  Your shower will see far more water than your roof will in a year. For that reason, be sure that you hire a Certified Tile Installer.  You need to protect the investment you have made in your home.

Wrapping Up

A curbless shower will fit any design and bathroom type.  If you are looking for an upgrade that won’t kill the budget and still turn some heads, a zero entry shower is what you’re looking for.  If you have an accessibility need, certainly feel free to contact me directly.  I am here to help guide you in the process of successfully remodeling your bathroom.  Together, we can make your dream bathroom a reality.  Finally, I invite you to check out our tile store Legacy Bath and Tile in Columbia, MO.

shower installer Columbia Missouri

21st Century Tile Shower Installer

shower installer Columbia MOWhy are we still building bathrooms today like we did 20 years ago or more?  A good shower installer knows that using technology to their advantage is a good thing.  We aren’t going backward in time, technology keeps getting smarter.  The bathroom is arguably one of the most important rooms in our homes.  It’s time we look at upgrading it to reduce stress and increase happiness.  A smart shower isn’t lacking in function and blends nicely into the rest of the shower.  Let’s look at some benefits a smart shower has over traditional showers.

Style and Functionality

A touchscreen shower has the ability to integrate many features into your shower.  With the push of a button you can listen to your favorite artist using Bluetooth speakers.  You can also adjust the light level and set the mood.  Imagine taking a steam in a dim light as beach waves crash against the shore.  You can even have two temperatures in your shower simultaneously.  This can be a reality in your home.  As a shower installer I keep up with the latest trends in technology.  Of course you can also have a multi-function shower without the touchscreen.

What Can A Shower Installer Do For You

As a shower installer there’s a lot I can do for my customers.  I am happy to sit down with you and discuss your shower build.  A smart shower is something that takes a lot of planning and forethought.Shower installer near me Mid-Missouri  You don’t want to hire just any shower installer for your smart shower installation.  You want a shower installer that has installed a smart shower before.  I can help you pick the brand that’s right for you with the controls you need.  What can your shower do for you?  That is the question you need to ask yourself before hiring a shower installer.

Health Benefits

Shower installer Columbia MOPlan on  getting the most out of your bathroom by having a  smart shower installed in your home. I also recommend you  consider adding a steam generator as well.  A steam shower adds many health benefits including detoxing your system, relieving sore muscles and clearing sinuses.  A smart shower is a large investment,  a qualified shower installer is a must.  You can really be in trouble hiring someone that lacks experience and expertise.  A smart shower will also help with resale of your home.  Not only will it be a convenience for you, but the new owner will appreciate it as well.   I offer a lifetime warranty on tile installations and will maintain whatever the manufacturer warranty is on the shower system.


Steam Shower Columbia Missouri custom tile installation

Live Happier and Healthier with a Steam Shower

Steam shower Columbia Missouri touch screen controlA steam shower is a great addition to any bathroom. It’s easy to add steam to a tiled shower, I definitely recommend looking into one for your home.  Adding steam has many health benefits, you’re certainly aware of that.  Below you will find my top five reasons you should add a steam shower to your home.

Faster Recovery

Perhaps the best reason you should add steam is to decrease your recovery time from working out.  If  your job is physically demanding a steam shower can help your recovery as well.  Gyms know that steam decreases recovery time, that is why steam showers are common there.   As we age we need all the help we can get decreasing our recovery time.  Of course there are other benefits as well.

Improved Circulation

Due to the increase in temperature your veins widen making it easier for blood to flow.  This increases circulation to all parts of the body, also assisting in faster recovery.  Increasing the blood flow also reduces soreness and pain from sore muscles.

Detoxes your Body

The increase in temperature causes your body to sweat.  As you sweat the toxins and chemicals leave your body, leaving you a little healthier.

Good for the Environment

Unlike a jetted tub, a steam shower uses very little water.  The average steam shower uses less than 2 gallons of water for a twenty minute steam.  Another benefit is that a steam shower heats up faster as well.  Instead of waiting several minutes for your bathtub to fill up, steam will typically start in less than a minute.  Adding steam to your shower also allows you to take a steam, then immediately shower all in the same room.  When you shower the steam condenses back to water vapor and goes down the drain. There’s no need for special venting that way.

Other Benefits of a Steam Shower

Steam can act as a moisturizer improving your skin and make you look younger.  Since steam increases your heart rate your metabolism also increases.  A steam shower can also reduce stress and make it easier to fight off colds.  There are many benefits to adding a steam shower in your home.

Can I Just Crank up my Existing Shower?

A steam shower is far more different than just trying to turn the heat up on your shower head.  For starters, the water coming out of your shower actually cools the space preventing you from reaching the steam shower Columbia Missourineeded temperature.  A typical steam shower should reach room temperatures of 110 degrees Fahrenheit to 120 degrees.  This is also what sets a tiled shower steam unit apart from the spaceship looking things you can buy online.  Many of those units can’t go over 100 degrees

In Conclusion

Steam showers are great for most anyone.  I wouldn’t recommend adding one to your home if you are diabetic or have high blood pressure.  If improving your health is something that interests you, talk to me about installing a steam shower in your home.  I am happy to walk you through our process and explain in more detail the benefits you will see.  As with all our tile installations, you will get a lifetime warranty on the tile assembly.  For the best tile selection in Columbia, check out our store Legacy Bath & Tile.

Tile Shower Design, Columbia MO, Certified Tile Installer

Tile Shower Design Must Haves For Your Bathroom

To truly unleash your bathrooms potential the tile shower design is critical.  Your tile shower is the focal point of the bathroom. Don’t be afraid to show it off.  You will be azmazed at what your tiled shower can do for you.  Remodeling your bathroom is typically a one time expense, don’t cheap out on getting what you want.  A properly designed tile shower can improve your health and reduce stress.  Don’t believe me, continue reading to see what I’m talking about.

The Shower Faucet

For me, the first element in tile shower design is the faucet itself.  The type of faucet you choose says a lot about you.  The faucet is also where your health and happiness comes into play as well.  Water can massage in addition to clean, imagine a shower experience that you can completely control.  I’m talking about body sprays, handheld shower, rainhead units or even a waterfall.  I can  integrate these features into your tile shower design effortlessly.  To truly reduce stress and increase overall health consider adding a steam shower.  Talk about creating a unique experience and one that you won’t forget.  You could finally have a true spa in your very own bathroom.

Other Tile Shower Design Considerations

I would strongly suggest staying away from natural stone as part of your tile shower design.  Natural stone is typically very soft and will be difficult to maintain.  I recommend porcelain tile with a stone pattern instead. Unlike stone, porcelain tile is very low maintenance and will stay looking new for a long time.  Like stone tile, porcelain tile is available in similar sizes shapes and colors.

Other Considerations

I would consider a curbless shower as they are visually very pleasing and allow for easier entry.  A frameless shower door will also compliment the shower nicely as well.  A shower enclosure will also help retain heat, a very important feature if hot showers are important to you.  In conclusion, a tile shower design will have a big impact on your daily life.  Don’t trust just anyone with this important task.  I also recommend hiring qualified labor for your project as well.  Nothing is worse than spending money on a tile shower design and it fails.  Read about our tile shower installation method as well as our lifetime warranty for tile installations.

Trusting Your Tile Contractor

Tile contractor Columbia MOAny time you hire a tile contractor  to work on your home trust is an important factor.  What items are most important to you when deciding who you should hire for your next project?  The purpose of this post is to point out how I approach new projects.  There’s a lot that goes into planning a successful project, more than just installing the tile anyway.

What Makes Me Different

Protecting my customers both from failed jobs and the construction process are both very important to me.  I continually educate myself in proper tile installation and techniques to guard against a job failure.  The education opportunities I take advantage of also have many manufacturer’s there as well.  I take being a tile contractor seriously.  To protect your home I use drop cloths, plastic sheeting and HEPA air scrubbers to collect dust.  Your home shouldn’t be a danger zone, and you shouldn’t have to move out because you’re renovating a room.  I work hard to keep you satisfied and as stress free as possible.  A low stress work environment leads to better quality work all the way around.

A Tile Contractor Works For You

As a tile contractor its my job to make your dream bathroom a reality.  I have a lot of control over your project, everything is adjustable.  Your fixture heights, niche locations and size, tile layout are all done ahead of time.  I work hard to cover every detail of the job with you before we start.  You have the final say in what your project will be.  This is your home, I want to make you happy.

A Strong Team

It takes a lot more than just me, the tile contractor,  to make your dreams a reality.  I hire great employees that care about your home as much as I do.  While I am on site during the installation, I do sometimes have to run an errand.  I like knowing that even if I’m away your home is still in good hands.  My wife, Jennifer, also works hard to coordinate your project start date with you.  In addition to that she assists with tile design and layout options.

Lifetime Warranty

All our tile projects qualify for a lifetime warranty.  I say that because if I can’t warranty your job for life, I won’t do it.  I won’t compromise best installation practices to land a job.  As a tile contractor, I have too much pride for that.  In addition to my warranty, you can also register your project with the manufacturer as well.  Registering with the manufacturer gives you their lifetime warranty.  To answer more questions visit our FAQ page.